Shop By Category
Your Cart

Goerend Transmission Products

Goerend Transmissions offers the best performance built 47RH, 47RE, & 48RE transmissions, along with life-time triple disk torque converters.

They also offer valve bodies, high capacity transmission pans, billet input, output, & intermediate shafts, and much more!

Brand: Goerend Transmissions Part Number: R-FFCL
OE cooler bypass valves allow transmission fluid to bypass the cooler and flow right back into the transmission, quickly raising the transmission temperature. These OE cooler bypass valves tend to fail, causing the transmission and torque converter to overheat and cause major damage. Our Full Flow C..
$89.00
Brand: Goerend Transmissions Part Number: ATC-L5P
Goerend Difference:Designed and manufactured in-house from start to finishK-factor and torque ratio tested on in-house dynamometerBillet steel coverMade from steel forgings to reduce porosityMulti-bolt patternBillet steel pistonMade from steel forgings to reduce porosityBillet steel statorDesigned t..
$1,545.00
Brand: Goerend Transmissions Part Number: R-FFCL (2019+)
OE cooler bypass valves allow transmission fluid to bypass the cooler and flow right back into the transmission, quickly raising the transmission temperature. These OE cooler bypass valves tend to fail, causing the transmission and torque converter to overheat and cause major damage. Our Full Flow C..
$89.00
Brand: Goerend Transmissions Part Number: D121-109 G Kit
The Goerend Bellville spring is .020” thicker than stock for added strength. The late .780" apply piston is the only style apply piston that should be used with the heavy Bellville spring. Our Laser cut, steel spacer is thinner than the plastic stock spacer to keep the waved snap ring in its proper ..
$99.00
Brand: Goerend Transmissions Part Number: 72960-16K BLK
Dodge trucks pulling heavy loads or boosted to 500–600HP are at high risk for overdrive burnup due to the stock transmission’s insufficient clutch capacity and fragile OE clutches. Even small amounts of heat and extra torque will push the thin (.034"), single-sided clutches over the edge, disto..
$699.00
Brand: Goerend Transmissions Part Number: D121-104-Goerend-SP
Fits: 1994-2007 Dodge Cummins 5.9L The 23-spline billet input shaft is custom forged from High Strength 300M steel and incorporates a 23-tooth input spline and 62-tooth clutch spline. This shaft utilizes a heavy duty one-piece design, is OE seal compatible, and comes with Goerend lube modificatio..
$649.00
Brand: Goerend Transmissions Part Number: A101-32C2BILLET
The Goerend C2 clutch hub is more durable than OE hubs. It is made out of forged 4140 high strength steel and has a thicker snout to prevent twisting from high powered engines and shift bindups. This C2 clutch hub should be used in trucks with over 750 HP and in trucks used for pulling, drag racing ..
$449.00
Brand: Goerend Transmissions Part Number: A139-10 5 SPEED BILLET
OE P2 planetary carriers in are known to get stripped easily. Stripping can cause complete transmission failure. The Goerend P2 planetary carrier snout made of forged 4140 high strength steel to prevent spline twisting and stripping from too high torque engines and shift bindups.Goerend Part Number:..
$755.00
Brand: Goerend Transmissions Part Number: A139-10 6 SPEED BILLET
OE P2 planetary carriers in are known to get stripped easily. Stripping can cause complete transmission failure. The Goerend P2 planetary carrier snout made of forged 4140 high strength steel to prevent spline twisting and stripping from too high torque engines and shift bindups.Goerend Part Number:..
$755.00
Brand: Goerend Transmissions Part Number: FTC-6Rxx
Goerend Difference:Designed and manufactured in-house from start to finishBillet steel coverMade from steel forgings to reduce porosityBillet steel pistonMade from steel forgings to reduce porosityBillet steel statorDesigned to rotate better when going into coupling modeGuaranteed to never breakPate..
$2,200.00
Brand: Goerend Transmissions Part Number: FTC-4Fxx
Some of the first steps of designing new products is by identifying the weak points and problem areas of the existing parts and figuring out how to improve and fix them. In the case of the Ford 4R100 torque converter, the main factory components are the weak points. The impeller and turbine being ma..
$1,395.00
Brand: Goerend Transmissions Part Number: 121-104 Goerend-SP
The 23-spline billet input shaft is custom forged from High Strength 300 maraging steel and incorporates a 23-tooth input spline and 62-tooth clutch spline. This shaft utilizes a heavy duty one-piece design, is OE seal compatible, and comes with Goerend lube modifications. This shaft does not fit no..
$649.00
Brand: Goerend Transmissions Part Number: D-PAN-4748-LOGO
Designed by Dave Goerend and staff, who have been researching and developing to make their own pan to fit their needs and are now sharing these results. Goerend Difference: Constructed of lightweight cast-aluminum Efficient heat dissipation and durability Holds approximately 2.5 quarts ..
$299.00
Brand: Goerend Transmissions Part Number: GT TRPL TC 4748RE
Goerend Difference:Designed and manufactured in-house from start to finishK-factor and torque ratio tested on in-house dynamometerBillet steel coverMade from steel forgings to reduce porosityMulti-bolt patternBillet steel pistonMade from steel forgings to reduce porosityBillet steel statorDesigned t..
$1,095.00
Brand: Goerend Transmissions Part Number: GTVALVEBODY
Call to Order!  Pricing May Change Based On Your Specifications! 3-4 Week Build Time! Call to Confirm! 03-07 Dodge 5.9L Cummins Diesel Valve body for trucks equipped with the 48RE automatic transmission. Great for Race, Daily Driving, or Towing Application Make your transmission sh..
$0.00
Brand: Goerend Transmissions Part Number: D-GT2KIT-48RE
The Goerend 48RE GT2 master rebuild kit includes all the parts needed to update and rebuild a working transmission. This kit includes a complete overdrive bearing kit, complete bushing kit, thrust washer kit, and sun gear not found in the GT1 kit. We use the best OE parts, performance aftermarket pa..
$964.00
Brand: Goerend Transmissions Part Number: 727/518
Dodge 727 Single Disk Cummins Torque Converter by Goerend Transmission Works in 1989-1993 Dodge 727 or 518 Automatic Transmissions. Goerend Converters were developed using a chasssis dyno, transmission dyno, & live trucks.  3 year warranty! Warranty does not cover loss of use, time, ..
$650.00
Brand: Goerend Transmissions Part Number: D-GT2KIT-47RE
The Goerend 47RE GT2 master rebuild kit includes all the parts needed to update and rebuild a working transmission. This kit includes a complete overdrive bearing kit, complete bushing kit, thrust washer kit and sun gear not found in the GT1 kit. We use the best OE parts, performance aftermarket par..
$964.00
Brand: Goerend Transmissions Part Number: D-PAN-68RFE-LOGO
Goerend 68RFE Transmission Pan for Dodge Diesel model years 2007.5 & Newer Goerend Difference: Constructed of lightweight cast-aluminum Efficient heat dissipation and durability Holds approximately four quarts more fluid than the OE version Patented sloped floor design Resul..
$329.00
Brand: Goerend Transmissions Part Number: GFP-5.9
Goerend Billet Flex Plate - (Non SFI Approved) 47RE, 48RE, 47RH  5.9L As the horsepower and pulling weight of the vehicle increases, so does the strain on the flexplate, which is why the Goerend Billet Steel Flexplate is perfect for towing, daily driving, and drag racing. This flexplate is u..
$349.00
Brand: Goerend Transmissions Part Number: 47/48RE VBA
This item wires into the computer harness and prevents the computer from throwing your automatic transmission into "limp mode" with higher pressure valve bodies. When a high-pressure valve body is installed in a truck, the higher governor pressure is detected by the computer and the transmission is..
$55.00
Brand: Goerend Transmissions Part Number: GFP-5.9 SFI
This Goerend Transmission SFI APPROVED billet flex plate replaces the stamped factory piece that is prone to failure when under high power levels. As the horsepower and pulling weight of the truck increases, so does the strain on the flex plate - that is why this flex plate is perfect for towing, da..
$374.00
Brand: Goerend Transmissions Part Number: D-GT2KIT-47RH
The Goerend 47RH GT2 master rebuild kit includes all the parts needed to update and rebuild a working transmission. This kit includes a complete overdrive bearing kit, complete bushing kit, thrust washer kit and sun gear not found in the GT1 kit. We use the best OE parts, performance aftermarket par..
$964.00
Brand: Goerend Transmissions Part Number: D73-LSA 3.8 KIT
The billet lever, strap, & anchor are an extremely important and beneficial addition to any Goerend Valve Body! Dave highly recommends using these parts with any high pressure valve body builds. If the factory apply lever breaks, the transmission must come out to replace it. In addition, we reco..
$89.00
Brand: Goerend Transmissions Part Number: DTC-X_SINGLE
96-02 Dodge 47RE Single Disk Torque Converter by Goerend TransmissionGoerend Difference:Designed and manufactured in-house from start to finishK-factor and torque ratio tested on in-house dynamometerBillet steel coverMade from steel forgings to reduce porosityMulti-bolt patternBillet steel pistonMad..
$800.00
Brand: Goerend Transmissions Part Number: DTC-68-X
Goerend DifferenceDesigned and manufactured in-house from start to finishK-factor and torque ratio tested on in-house dynamometerBillet steel coverMade from steel forgings to reduce porosityMulti-bolt patternBillet steel pistonMade from steel forgings to reduce porosityBillet steel statorDesigned to..
$1,395.00
Brand: Goerend Transmissions Part Number: DTC-68-DBL
With a Goerend double disk torque converter you get increased torque delivered to the rear wheels, with less energy loss in the fluid coupling between the engine and transmission. Goerend Converters were developed using a chasssis dyno, transmission dyno, & live trucks.  Double Disc 15 Bla..
$990.00
Brand: Goerend Transmissions Part Number: GFP-6.7
Goerend Billet Flex Plate - 68RFE The Goerend 68RFE Billet Steel Flexplate utilizes forged steel construction and replaces the stamped factory piece that is prone to failure when under high power levels. As the horsepower and pulling weight of the truck increases, so does the strain on the flexpl..
$349.00
Brand: Goerend Transmissions Part Number: D-GT1KIT-48RE
The Goerend 48RE GT1 basic rebuild kit includes all the parts needed to update and rebuild a working transmission. We use the best OE parts, performance aftermarket parts and build our own parts in all Goerend rebuild kits. This kit is intended for a professional transmission technician who has prop..
$674.00
Brand: Goerend Transmissions Part Number: A-GT6KIT
Goerend Allison 6 speed automatic transmission master rebuild kit. This kit is intended for a professional transmission technician who has proper equipment to clean, inspect, test, and rebuild a transmission. Goerend Transmission is not a technical or training service. Customers of this kit are e..
$3,699.00
Brand: Goerend Transmissions Part Number: A-GT BILLET PTO COVER-LOGO
The Goerend PTO cover funnels oil to a hole in the transmission case that supplies lube oil directly to the C3 clutches. This oil would otherwise return to the transmission pan unused. This patented design is able to lube and cool the hard working C3 clutches.   Use the jig tool to insure..
$90.00
Brand: Goerend Transmissions Part Number: F-PAN-E4OD/4R100-LOGO
Will fit Ford E4OD and 4R100 transmissions. Approximately 1989-2002.Goerend Difference:Constructed of lightweight cast-aluminumEfficient heat dissipation and durabilityHolds approximately three quarts more fluid than the OE versionPatented sloped floor designResults in 100% fluid drainageMagnetic dr..
$349.00
Brand: Goerend Transmissions Part Number: ATC-X
We design the Allison converter components here at Goerend Transmission, and also manufacture them from start to finish using our eight in-house CNC machines. This ensures accurate dimensions that work with your transmission. This also means you are communicating directly to the manufacturer, which ..
$1,545.00
Brand: Goerend Transmissions Part Number: D-GT1KIT-47RE
The Goerend 47RE GT1 basic rebuild kit includes all the parts needed to update and rebuild a working transmission. We use the best OE parts, performance aftermarket parts and build our own parts in all Goerend rebuild kits. This kit is intended for a professional transmission technician who has prop..
$664.00
Brand: Goerend Transmissions Part Number: D212-383
Overdrive Lock-Up Solenoid, '96-'99 Dodge Old Part Number: 12420B/52118500 Old Part Number: 22954B SL..
$129.00
Brand: Goerend Transmissions Part Number: D12432A/4617210
Governor Pressure Solenoid '96-07 47RE & 48RE Dodge..
$112.00
Brand: Goerend Transmissions Part Number: D-GT1KIT-47RH
Goerend Basic Overhaul Kit for the 94-95 Dodge 47RH TransmissionIncludes:All factory (Borg Warner or Raybestos) clutch plates & steel platesAll gaskets-seals-sealing ringsRaybestos pro series front bandRaybestos oem triple wrap rear bandBillet 3.8 front band apply arm-strut-anchorSonnax billet 4..
$664.00
Brand: Goerend Transmissions Part Number: A-PAN-A1000-KIT
Designed by Dave Goerend and staff, who have been researching and developing to make their own pan to fit their needs and are now sharing these results. Goerend Difference:Constructed of lightweight cast-aluminumEfficient heat dissipation and durabilityHolds approximately three quarts more fluid th..
$319.00
Brand: Goerend Transmissions Part Number: A-GT5KIT
This master rebuild kit is intended for a professional transmission technician who has proper equipment to clean, inspect, test, and rebuild a transmission. Goerend is not a technical or training service. Customers of this kit are expected to have access to and be proficient with necessary equipment..
$3,549.00
Showing 1 to 39 of 39 (1 Pages)