







07.5-12 Dodge 6.7L Cummins Diesel GDP Air Boss Grid Heater Delete
$248.99
- Part Number: 07510-ABIP
- Est. Ship Time: Usually Ships in 2-3 Business Days

SSL SECURE
TRANSACTION

AUTHENTIC
PRODUCTS

GUARANTEED PREMIUM
QUALITY

A+ Rating
More from this brand
Starting From $299.99
Starting From $239.99
GDP 6.7L "AIR-BOSS 67" Grid Heater Delete
EGT's running too high? Can't use all of the fuel you have available? The 6.7L Air-Boss 67 Grid Heater Delete gives the largest flow increase possible short of milling the cast plenum off of the head and going to a fabricated intake such as the ZZ Fab or Hellman unit.
The Air-Boss 67 is not just a replacement flat plate. The Air-Boss 67 Grid Heater Delete is a billet aluminum, internally elevated plenum cover designed to flow as much air as possible to cylinders 4, 5, and 6. With careful machining we were able to gain a full .220" of internal height while still allowing the use of the factory mounting hardware.
The new factory grid heater used on the 6.7L trucks is the worst design yet for airflow. Not only is the flow area much smaller than needed but the heater actually extends down INSIDE of the plenum. This not only causes turbulence but reduces the needed turning radius area by 40%. The Air-Boss 67 Grid Heater Delete removes the restrictive factory grid heater and opens up the turning radius and internal plenum area to the starving rear cylinders.
Air-Boss 67 elevated intake plenums are compatible with all stock style intake manifolds and most aftermarket units such as the WCC and BOD units.*
The increased airflow provided by the Air-Boss 67 reduces EGT's and allow you to run even higher fueling levels!
For cold weather applications that still require a grid heater please see the new GDP "Arctic Heat" High Flow 6.7L Grid Heater Relocation Kit shown here. When combined with the Air-Boss 67 you have the highest flowing cold weather package available on the market.
Kit includes Air-Boss 67 intake plate, factory gaskets, fuel rail stand-offs, and intake temperature sensor sealing ring.
*NOTE: Thanks to Jaxon at Wild Card Customs all WCC Intake Manifolds built after 01-01-2010 are compatible with the Air-Boss 67 Grid Heater delete.
EGT's running too high? Can't use all of the fuel you have available? The 6.7L Air-Boss 67 Grid Heater Delete gives the largest flow increase possible short of milling the cast plenum off of the head and going to a fabricated intake such as the ZZ Fab or Hellman unit.
The Air-Boss 67 is not just a replacement flat plate. The Air-Boss 67 Grid Heater Delete is a billet aluminum, internally elevated plenum cover designed to flow as much air as possible to cylinders 4, 5, and 6. With careful machining we were able to gain a full .220" of internal height while still allowing the use of the factory mounting hardware.
The new factory grid heater used on the 6.7L trucks is the worst design yet for airflow. Not only is the flow area much smaller than needed but the heater actually extends down INSIDE of the plenum. This not only causes turbulence but reduces the needed turning radius area by 40%. The Air-Boss 67 Grid Heater Delete removes the restrictive factory grid heater and opens up the turning radius and internal plenum area to the starving rear cylinders.
Air-Boss 67 elevated intake plenums are compatible with all stock style intake manifolds and most aftermarket units such as the WCC and BOD units.*
The increased airflow provided by the Air-Boss 67 reduces EGT's and allow you to run even higher fueling levels!
For cold weather applications that still require a grid heater please see the new GDP "Arctic Heat" High Flow 6.7L Grid Heater Relocation Kit shown here. When combined with the Air-Boss 67 you have the highest flowing cold weather package available on the market.
Kit includes Air-Boss 67 intake plate, factory gaskets, fuel rail stand-offs, and intake temperature sensor sealing ring.
*NOTE: Thanks to Jaxon at Wild Card Customs all WCC Intake Manifolds built after 01-01-2010 are compatible with the Air-Boss 67 Grid Heater delete.

The Shibby Engineering 6.7 Grid Heater Delete includes:
OEM Gaskets top and bottom
Machined out of 6061-T6 Billet aluminum
Rail Spacer..
$149.99
GDP 6.7L "AIR-BOSS 67" Grid Heater Delete
EGT's running too high? Can't use all of the fuel you have available? The 6.7L Air-Boss 67 Grid..
$248.99
Discontinued (Updated 1/18/2024)
Direct replacement, Mopar part.
2 required, 2 included.
Mopar: 5086631AA replaced by 68188370AA
 ..
$0.00
'03-'07 5.9L "Air-Boss CR" Intake Plenum Cover & Grid Heater Delete Kit
EGT's running too high? Can't use all of the fuel you have av..
$349.99
'98.5-'02 5.9L "Air-Boss VP" Intake Plenum Cover & Grid Heater Delete Kit
EGT's running too high? Can't use all of the fuel you have ..
$319.99
NOTE: For code free installation of the 6.7L Filter Eliminator the "Water in Fuel" sensor must be removed from the stock fuel filter and plu..
$74.99
DISCONTINUED
'07.5-'09 "Arctic Heat" 6.7L 3.50" High Flow Grid Heater
Note: Not for use on 2010+ vehicles.
The first and o..
$0.00
AutoMeter Phantom II 0-2000 Degree Pyrometer Stepper Motor. Combines traditional hi-performance meters with bold outlined white on white dials, revers..
$267.33
Discontinued (Updated 2/29/2024)
Mega-Flo S-3 Cummins 6.7L Intake Manifold
Fits 2007.5-2013 Dodge 6.7L Cummins Diesels.
Fits pickups &..
$0.00
The easiest transmission mod you can make! Does not fit any Dodge or Ram CAB & CHASSIS truck.. they have a different transmission.
High volumes of..
$355.95
Recommended for high hp, high RPM engine builds running a cast iron cam. They have a larger cam "footprint" than the stock 12 & 24 Valve Cummins T..
$26.75
This item works on 07.5-09 trucks only with the 4 wire throttle valve plug.
Features:
Two OEM connectors for use with unplugged EGR bypass valves..
$13.25
Bladerunner Intercoolers represent the next generation of intercoolers. The Bladerunner intercoolers utilize a 3" bar and plate design that outperf..
$2,191.00
Backordered with No ETA (Updated on 6/10/2025)
12mm Head stud kit for the 98.5-2012 Dodge 5.9L & 6.7L 24 Valve Cummins Turbo Diese..
$486.62
2007.5-2012 6.7L Cummins Upper Engine Head Gasket Set
Includes:
1x M22 O-Ring Seal 3089240
2x O-Ring Seal 3678603
2x M18 O-Ring Seal 3678..
$823.55
Industrial Injection CP3 Stg. 1 BOP (Bag of Parts) kit for 2007.5-2018 Dodge 6.7L Cummins
The stage 1 For the 6.7 Cummins, "Do it yourself" kit is go..
$491.59
This Cumins barring tool is used to rotate the engine by inserting it into a port located on the bell housing/engine adapter plate.It provides an easy..
$121.55
Remove the Connector Tube From the Cummins CR Without Damaging the Threads!
Use the right tool and reuse your Cummins crossover tubes when ch..
$21.25
Does your 6.7L Cummins have a blown head gasket?
Join the club. At a minimum, make sure your have your head surfaced to ensure it is flat. We also ..
$168.29
98.5-12 24V Dodge Cummins Valve Spring Compressor
The Cummins Valve Spring Compressor (CVSC010) by Tork Tools, features a tapered design, that redu..
$86.99
Power-Flo intake manifolds for the '03-'07 Dodge Rams are the ones you've been looking for! The Power-Flo is a direct factory replacement for the r..
$299.99
GDP 6.7L "AIR-BOSS 67" Grid Heater Delete for Pickup Applications
EGT's running too high? Can't use all of the fuel you have available? T..
$239.99
'98.5-'02 5.9L "Air-Boss VP" Intake Plenum Cover & Grid Heater Delete Kit
EGT's running too high? Can't use all of the fuel you have ..
$319.99
GDP 6.7L "AIR-BOSS 67" Grid Heater Delete for '07.5-'18 Cab & Chassis Applications
That's right, we didn't forget about the C&C o..
$255.99
'03-'07 5.9L "Air-Boss CR" Intake Plenum Cover & Grid Heater Delete Kit
EGT's running too high? Can't use all of the fuel you have av..
$349.99
Thru testing we have discovered that twin CP-3's require lower feed pressures (15 to 20 psi) to avoid high rail pressure codes at idle. Now we have th..
$174.99
'03-'07 Common Rail Injector Holding Tool
Swapping CR injector tips yourself? Afraid of damaging the injectors bodies in your vise? The GDP injecto..
$19.99
'07.5 + Common Rail Injector Holding Tool
Swapping CR injector tips yourself? Afraid of damaging the injectors bodies in your vise? The GDP injecto..
$19.99
6.7L Bosch Fuel Rail & Injector Line Package
Complete Bosch 6.7L fuel rail and injector line package for use with our Mega-Rail Conversion Kit...
$1,310.39
07.5-12 Dodge 6.7L GDP TORKER-I 50 HP Injector NozzlesLooking for stump pulling torque? The GDP 6.7L TORKER nozzles put the power down! TORKER Nozzl..
$774.99
07.5-12 Dodge 6.7L GDP TORKER-II 75 HP Injector NozzlesLooking for stump pulling torque? The GDP 6.7L TORKER nozzles put the power down! TORKER Nozz..
$784.99
07.5-12 Dodge 6.7L GDP TORKER-III 100 HP Injector Nozzles
Looking for stump pulling torque? The GDP 6.7L TORKER nozzles put the power down! TORKER No..
$794.99
07.5-12 Dodge 6.7L GDP TORKER-IV 125 HP Injector NozzlesLooking for stump pulling torque? The GDP 6.7L TORKER nozzles put the power down! TORKER Noz..
$899.99
07.5-12 Dodge 6.7L GDP TORKER-V 150HP Injector Nozzles
Looking for stump pulling torque? The GDP 6.7L TORKER nozzles put the power down! TORKER Nozzl..
$924.99
13-18 6.7L Cummins GDP TORKER-I 50 HP Injector Nozzles
Looking for stump pulling torque? The GDP 6.7L TORKER nozzles put the power down! TORKER Nozzl..
$749.99
Custom Individual Runner Intake Manifold for the 89-98 Cummins 5.9L
Features:
Equal Air Distribution
3.5 Inch V-Band Inlet. V-band clamp is..
$950.00
Custom Individual Runner Intake Manifold for the 98.5-02 Cummins 24V
Features:
Equal Air Distribution
3 Inch V-Band Inlet. V-band clamp is ..
$849.00
-Arc Flow Intake, 2003-2005 Dodge Common Rail 5.9L, Cummins, Pre tapped for Gauges and water injection, Includes Powder Coating and Machining. The ATS..
$317.13
Pusher Intake Manifold for Cummins 5.9L turbo diesel engines in 2003-2007 Dodge Ram trucks.
All Pusher intake manifolds can be used with or witho..
$174.99
Features:
In recent testing the BladeRunner intake manifold outflowed the factory intake by 34% and resulting in gains of up to 11 HP and 27 lbs. x..
$593.00
WHAT IT DOES
Your Cummins engine consumes a massive amount of air and struggles to breathe through its tiny, squashe..
Starting From $968.00
What it does
The Monster-Ram improves airflow from the intercooler. It flows 72.7 lbs/min MAF (Mass Air Flow) with Banks’ High-Flow Heater an..
Starting From $968.00
Pusher intake manifold for Cummins 5.9L turbo diesel engines in 1994-1998 Dodge Ram trucks.
The Pusher 12v manifolds are hydro boost compatible and..
$184.99
Arc-Flow Intake Manifold, Black Powdercoat, 98.5-02 Cummins, Pre-tapped for gauges/water injection, Includes Powder Coating and Machining. The ATS Int..
$317.13
Blade Runner (Charged Manifold) Dodge Trucks- 98.5-02 L6-5.9L (td) Features Increase airflow by 32.9% over stock ..
$475.00
Pusher Intake Manifold for Cummins 5.9L turbo diesel engines in 1998.5-2002 Dodge Ram pickup trucks.
All Pusher intake manifolds can be used ..
$174.99
At Banks Power, just enough is never enough when it comes to engine airflow. Maximum power, performance and efficiency are the ultimate goals, but to ..
$498.00
At Banks Power, just enough is never enough when it comes to engine airflow. Maximum power, performance and efficiency are the ultimate goals, but to ..
$349.00
Features a larger plenum for increased airflow, and smooth radius turns to reduce turbulence and intake pressure losses. BD’s unique design positions ..
$339.95
S&B Intake Elbows are CNC Machined from a 6061 – T6 Aluminum andreplace your restrictive stock turbo inlet manifold. Our intake elbows maximize ai..
$249.00