Tools & Misc

TS1082 Ball Joint Press Set for 2003-2013.5 Ram 2500 and Ram 3500 with Original Equipment Ball Joints This 7 Piece Ball Joint Press Set is specifically tailored to press out and press in original equipment American Axle Manufacturing (AAM) Ball Joints in your 2003 to 2013.5 heavy-duty Dodge or ..

This G&R Diesel GRD67CM3027 Balancer Puller is the perfect component for your truck. Our 6.7 Cummins Harmonic Balancer Puller is built for you to be able to pull the balancer off of the engine without needing to remove the radiator.  This makes maintaining anything on the front of..

89-18 5.9L & 6.7L 12V/24V Dodge Cummins Injection Pump Gear Puller Tork Teknology specializes in designing and manufacturing tools for the Cummis 5.9 and 6.7 diesel. (The Duramax is next) Our lastest tool is the CGP020 injection pump gear puller for the Bosch VE, P7100, VP-44 and CP3...

Fits: 1989-2018 Dodge Ram 5.9L/6.7L Cummins, 3.9L Cummins 4BTThe CTA Tools Cummins Rear Crankshaft Seal Tool Allows you to replace the leaking seal in your 1989-2016 Dodge Ram 5.9L/6.7L Cummins or 3.9L Cummins 4BT. This tool is engineered to remove the old seal and install a new seal without damagin..

Cummins 24v Engine Lift Bracket, made to go in the rocker box holes to make lifting a fully dressed engine easy or just pulling a head for a head gasket job easier. Items included will be: – Engine Lift Bracket – Bolts to mount Engine Lift Bracket to the head. – Choice of raw o..

Makes changing out your valve springs while in the engine very easyWorks with both stock springs and aftermarket valve springs.Hamilton: 07-SC-002..

Does your diesel have High EGTs, Excessive SMOKE, Increased Turbo Lag, and Less Power than it used to? Let’s talk about boost leaks. Your truck needs air! Not a little bit of air. Your diesel engine needs all the incoming air it can get. Increasing air in the combustion process will help ma..

CTA Tools Cummins engine barring tool Designed to fit the flex plate teeth Insert the tool into the flywheel housing until it engages the ring gear Use with a 1/2" square drive tool (ratchet or breaker bar) to operate Applications: Dodge Pickups with the 3.9L, 5.9L, 6.7L & 8.3L ..

Hamilton Cams Cummins Engine Barring ToolNever struggle to turn your engine over by the harmonic balancer bolts again, Save your valuable time and get the job done faster with one of these tools.Used on the below applications3.9L Cummins5.9L Cummins6.7L Cummins8.3L CumminsHamilton: 07-C-BAR..

For use with Dodge Cummins VE, P7100, VP44 and CP3 Injection Pumps. The XDP XD134 is a finely machined tool that will remove the pump gear from the VE, P7100, VP-44 and CP3 injection pump. The increased depth on the step, prevents damage on the front cover. Competitive tools currently on the m..

Will work on - Most 93mm diameter filters that have 15 flutes Fleetguard: LF16035 LF3972 Mopar: MO-285 Mobil 1: M1-403 WIX: 57620XP 57620 MicroGard: MGL57620 Billet Aluminum for strength and durability. Accepts a 3/8" driver ratchet or a 3/4"/19MM socket/wrench for ..

The Alliant AP0083 Injector Brush Kit is a must have item in the toolbox of any 2003-2018 Dodge 5.9L & 6.7L Cummins technician. The Alliant Injector Brush Kit provides you with all the proper tools you need to clean the injector bore and seat while installing new injectors in an engine. Fea..

Ever wonder if you have a boost leak or you know you have one, but can't find it? We finally have the tool needed to locate all boost leaks, no matter how small in minutes. This is a great tool to use anytime you have opened the system for anything. Even the smallest of leaks (1-3lbs) can cause trem..

Ever wonder if you have a boost leak or you know you have one, but can't find it? We finally have the tool needed to locate all boost leaks, no matter how small in minutes. This is a great tool to use anytime you have opened the system for anything. Even the smallest of leaks (1-3lbs) can cause trem..

Cummins 12MM Head Stud Bottoming Tap We recommend you bottom-tap your engine block head-stud threads when installing 12mm ARP or A1 head studs to ensure maximum clamping force. Some Cummins blocks are not threaded completely. 12mm x 1.75 Picture for representation purposes only...

Please note that this product is usable on these series of vehicles:89 - 98 5.9L 12V Cummins98.5 - 07 5.9L 24V Cummins07.5 - 09 6.7L 24V Cummins10 - 15 6.7L 24V Cummins Turn over your Cummins with ease with this Cummins Crankshaft Barring Tool. It is much easier to use than the barring tool that in..

Remove the Connector Tube From the Cummins CR Without Damaging the Threads! Use the right tool and reuse your Cummins crossover tubes when changing to performance injectors. The common way of removing the Cummins CR crossover tube is to use a pair of Vise Grips. Sure, it works, but you risk damagi..

98.5-12 24V Dodge Cummins Valve Spring Compressor The Cummins Valve Spring Compressor (CVSC010) by Tork Tools, features a tapered design, that reduces the chance of losing a valve keeper. There is nothing more frustrating than losing a valve keeper, especially when you need your Dodge Cummins 24V f..

GS33491For Use On Rear Gear Train EnginesRepair Sleeve Tool..

ARP Ring Compressors are CNC-machined from 6061-T6 billet tube material with a true radius for every bore diameter. The true radius design is far superior to conventional "tapered" devices and widely used by professional engine builders. Compressors are relieved on the bottom for wire O-ri..

Picture for representation only.Includes volume one & two.Cummins:  4021271..

Snap On 89-07 Dodge 5.9L Cummins Engine Barring Tool Used to rotate the engine for making valve and injection pump adjustments on Cummins and J.I. Case 3.9L, 5.9L and 8.3L "B" and "C" Series engines. 3/8" female square drive. Snap-On: YA9565A Snap-On Items ship within 1-3 business days. Please ke..

Cummins 14MM Head & Main Stud Bottoming Tap 14mm x 2.00 Picture for representation purposes only...

NHRA legal driveline loops for 03 – 07 Dodge Cummins pickups. -Includes both front and rear loops, for four wheel drive vehicles. Hellmann Performance part number: DRVLNLOOPS..

Factory replacement hood strut for 2003-2009 Dodge Ram trucks. Mopar part number: 55276321AC..

Features 0-100 PSI Range Accuracy: 2.5% FS Large 2.25” dial face for easy viewing Sure grip rubber shock isolation boot 13.75“ Stainless braided line Angled chuck enables easy measuring Mechanical pressure release valve Rugged carrying case 100 PSI gauge with Auto Meter's signature raci..

There are 8 per container, needs 32 on a truck. Please select 4 to do entire truck.Chrome plated lug nuts lead a tough life. Think about it, harsh elements, nasty corrosive wheel cleaners and lead-foot drivers. Not to mention overzealous impact guns and loose fitting lug wrenches. This kind of..

Change the valve springs in your 1998.5-2019 Dodge 5.9L & 6.7L Cummins with the XDP 24V Valve Spring Compressor Tool XD311. A must have in the tool box of any enthusiast, or professional technician. We all know using the right tools can cut hours off a job saving you time, money, and frustration..