BACKORDERED NO ETA - 033121
The Hamilton Cams 07-C-188/220 Camshaft for your 1989-2018 Dodge 5.9L/6.7L Cummins, has outperformed any other cam that Hamilton has tested against to date, from idle to 4,200 rpm. It is also the largest drop-in cam that Hamilton offers.Use with 64mm or larger single turbos or larger twins. Install intake on a 99 centerline, performance springs and pushrods are recommended. If you have had your head or block surfaced, you need to verify piston to valve clearance.
This is generally a drop in cam. If your head or block has been decked it is your responsibility to check your valve-piston clearance.
For it to be "drop in" on a 12v you will need no more than .018" piston protrusion and at least .055" valve face depth with a standard head gasket and a 99 intake centerline. On a 24v you will need no more than .018" piston protrusion and at least .038" valve face depth with a standard gasket. If you do not meet the minimum requirements for piston to valve clearance, don't worry, you can still run an oversize headgasket or cut valve reliefs.
- For Larger Singles & Compounds
- Best All-Around Performance Camshaft
- 1.020” wide lobes (widest in the aftermarket)
- Thicker core
- Every cam is drilled and tapped for a bolt on retainer
- The ONLY improved design cast cam on the market
Note: Zinc additive required
MUST USE HAMILTON CAMS TAPPETS TO MAINTAIN WARRANTY
Aggressive street/strip 188/220
INT: .310" Lift
EXH: .320" Lift
Shop around and ask others how wide their lobes are. If they say their cam is made just for them, ask them if their name is cast into the cam. I bet you it isn’t!
This cam came about after I couldn’t find a cam that did exactly what I wanted. Other cams worked well for towing but lacked major performance gains at higher RPM. Some cams showed marginal performance gains. Other cams spooled good but compromised efficiency to get the chargers lit. All the others were either old gasoline profiles that didn’t work well on the street or skimpy regrinds that were just a stab in the dark. Generally shrouded in secrecy, it can sometimes be quite a task to make an informed decision on diesel engine parts, especially a camshaft.
We are here to get you the absolute best cam for your specific truck, the first time.
Keep in mind that some Cummins cam gears have slightly different offsets built in. We suggest you inspect your tappet for wear. If they are worn either get them reground, or get new ones. If you are installing this cam in a 12v please replace factory tappets with tappets from a 1998-2002 24v for best longevity with low zinc oils. On engines seeing over 50psi or over 500hp we also suggest Hamilton heavy duty pushrods. Follow Cummins installation instructions, use adequate assembly lube, and add some of our zinc additive prior to startup, to ensure no break in damage due to the new low zinc oils on the market. Always keep the engine from starting until you visually verify that oil has made it all the way to the rocker arms.
To modify installed centerline, use Mopar performance offset keys part# p4349650. This offset key kit comes with 1°, 2°,3°,4° and 5° offset keys. Just remember 1° camshaft is 2° crankshaft since the crankshaft moves twice the speed of the cam. A basic degree wheel from Jegs or Summit, a small amount of wire and a dial indicator is all that is needed to degree a cam in.
Factory specifications for comparison:24V Stock:
INT: 159° .235” Lift
EX: 206° .297” Lift
24V 3rd gen:
INT: 163° .237” Lift
EX: 191° .299” Lift
110LB Springs are REQUIRED for 98.5+ Trucks running this cam or any cam with more than 300 lift or if you are running an aftermarket turbo with 40PSI boost or more.
Cam retainers are NOT to be used with 2003+ 5.9L & 6.7L Cummins engines unless your front cover has been modified for proper clearance.
Hamilton Cams are all Pre-Drilled for a cam gear bolt-on retainer. We recommend this option for 89-02 trucks.
Select option above to add a retainer.
Please review the cam shaft installation guide- CLICK HERE.
Part Number: 07-C-188/220