Injection Pumps & Upgrades

Dodge 94-98 Second Gen P-Pump: Adjustable Fuel Plate Kit for all P-Pump applications. Depending on pump and modifications 25-140 RWHP increase.Kit comes with Dynomite custom ground adjustable fuel plate, Boost Elbow, AFC Spring, and new AFC Housing fasteners. Excellent for almost every application f..

DescriptionThin copper washer for 12 Valve Cummins Injectors If you are running our 715, 753, 864, injector for your 12 Valve Dodge? You can tighten the nozzle spray angle to a tighter degree by using these .5mm washers. -Sold IndividuallyPart#: D3930324..

94-98 Dodge Ram 5.9 12V fuel linkage assembly bell crank lever. This is not a common part please be sure to provide your ESN in the ESN area when ordering so we can comfirm fitment. Was Cummins part number 3923158 now is Mopar part number 0488 6189 AA..

Timing tool kit for a Dodge Cummins with the inline P7100 fuel pump, otherwise known as "p-pump". These pumps came stock on 1994 to 1998 Dodge trucks. This timing tool kit allows you to set your injection pump timing in relation to crankshaft TDC very precisely. The factory method of setting the ti..

94-98 Dodge 5.9L 12 Valve Cummins Diesel Accelerator Linkage Assembly (OEM) Replaces Mopar- 5011849AB Cummins- 3932317..

If you are looking for an entire kit, CLICK HERE. Please, select the pieces you need above (prices subject to change without notice). To verify fitment on your exact application, please enter your engine serial number in the field. It is not mandatory, but you do risk receiving incorrect parts if ..

4000 RPM Governor Spring Kit (4K GSK)The Peak Diesel Governor Spring Kit is a special combination of springs and Piers' unique design on seats.This kit allows your engine to have full fueling to approximately 4000RPM, which greatly improves the driving experience of a stock truck, for trucks with in..

This plug will increase your rack travel for more fueling on your P7100 pump. AFC modifications are required to get the most out of this plug. The stock rack plug allows for 19mm of fuel rack travel.This "Mack" rack plug allows for 21mm of fuel rack travel.  Using this plug with 215 pumps may ret..

Cummins Adjustable Overflow Valve for the Bosch P7100 Injection Pump By Tork Tek ALL THE PROBLEMS WITH THE BOSCH OVERFLOW VALVE HAVE BEEN SOLVED! * ADJUST YOUR FUEL PRESSURE WITHOUT STRETCHING SPRINGS * BULLETPROOF DESIGN ELIMINATES HAMMERED SEATS * CURE FOR HARD STARTING AND LOW POWER * OFV01..

4000 RPM Governor Spring Kit with 12 Heavy Duty Valve 60lb Springs The Peak Diesel Governor Spring Kit is a special combination of Bosch springs and Piers' unique design on seats. This kit allows your engine to have full fueling to approximately 4000RPM, which greatly improves the driving experie..

Includes item number 24 in second picture. * Right Hand Thread & 1 1/4" Long We have found that SOME trucks may use a different style throttle linkage rod and will not work with these ends.. Please enter your ESN above. If you can't find it.. you may be better off ordering a complete throttle link..

Billet P7100 Pump Lock Pin. WAY cheaper than the junk plastic piece from Bosch! Contagious Diesel Performance part Number: CON9498PTLP..

VPMAX Big Line Dual Feed Kit for 94-98 12V Dodge Cummins trucks.Allows fuel to enter from two points to keep that hungry P Pump fed!Hose and fitting assembly comes with hoses attached to fittings as shown in picture ready to use. Tee has an -08 male JIC(AN) connection on all three ends. Metric adapt..

Front seal/o-ring for the P7100 injection pump found on 94-98 Dodge 5.9L 12 Valve Cummins trucks. Cummins: 3969698 Item number 5 in the picture...

Pure Diesel Power carries the complete line of cam plates for the P7100 injection pump by TST Products.Each kit comes complete with a new fuel curve cam plate, installation template, turbo boost control orifice (boost elbow), a new breakoff screw to replace the one removed, and installation instruct..

CUMMINS 14MM FUEL PRESSURE GAUGE SNUBBER   * SNUBBER ELIMINATES GAUGE NEEDLE BOUNCE* USE ON ANY FUEL SYSTEM WITH A 14MM X 1.5 THREAD* FASTER INSTALLATION THAN A NEEDLE VALVE  Now, it's easier than ever to install a fuel pressure gauge on your Cummins diesel! If you want to install a fue..

3000 RPM Governor Spring Kit (3K GSK) This kit allows your engine to have full fueling to approximately 3000RPM, which greatly improves the driving experience of a stock truck, for trucks with injectors and more, this kit is a must!The Peak Diesel Governor Spring Kit is a special combination of spr..

ONLY number 23 from second picture. * Left Hand Thread & 1 1/4" Long We have found that SOME trucks may use a different style throttle linkage rod and will not work with these ends.. Please enter your ESN above. If you can't find it.. you may be better off ordering a complete throttle linkage rod ..

AIR DOG AND FASS PUMP USERS INCREASE YOUR HORSE POWER AND FUEL PRESSURE WITH YOUR P7100 CUMMINSFor stock fuel systems, please check out OFV010 or OFV020 (OFV020 is biodiesel compatible).* OFV040HP Use with lightly modified Cummins diesels. * Fuel pressure range of 30 to 37 PSI. * Raises fuel pre..

High Flow Laser Cut Delivery Valves by SCHEID Diesel For the P7100 Injection Pump found on 94-98 Dodge 12 Valve Cummins Turbo Diesel.Do you need more fuel for your Dodge 12 valve cummins?Does your Cummins run poorly or after installing large injectors?Looking for more low end fueling?These delivery ..

The AFC Spring Kit allows you to achieve a good compromise of minimal smoke under acceleration with responsiveness. Kit Includes- Medium and light AFC springs for the P7100 pump, Allen screws, Allen wrenches, Break-off screws, Instructions are included, of course. It does not include the zinc bolts...

Delivery Valve SocketFor Installing or Removing the delivery valves on a P7100 Injection Pump..

These should be replaced when you replace/upgrade your delivery valves. Bosch Part number: 2410210033..

These heavier coil springs replace the stock governor coil springs to safely allow the engine to reach higher RPMs, so there is no momentum loss when shifting gears while towing up a hill. Kits are complete with all parts for 3000 and 4000 RPM and are recommended for vehicles that have 5 speed stand..

High Flow 024 Delivery Valves For 1994-1998 P7100 Pumps Found on Dodge 12V Cummins Turbo Diesels. Do you need more fuel for your Dodge 12 valve Cummins?Check out these 024 Delivery Valves. Bosch 024 Delivery Valve Kit will deliver more HP than the 191 Delivery Valves but not as much heat as the 02..

Cummins: 3920921 Item number 6 in the picture...

Cummins: 3920922 Item number 8 in the picture...

P7100 AFC Housing Gasket Part number: 2420206007..

This plug screws on to conceal the timing pin on a P7100 injection pump. This isn't a part you should really ever need to replace... unless you drop it and it ends up in never never land.. Seal/washer not included, please select above if you lost that too. DO NOT over tighten this cap.. or you WIL..

Cummins Adjustable Overflow Valve for the Bosch P7100 Injection Pump By Tork Tek ALL THE PROBLEMS WITH THE BOSCH OVERFLOW VALVE HAVE BEEN SOLVED! * ADJUST YOUR FUEL PRESSURE WITHOUT STRETCHING SPRINGS * BULLETPROOF DESIGN ELIMINATES HAMMERED SEATS * CURE FOR HARD STARTING AND LOW POWER * USE T..

Some P7100 injection pumps from mid-size trucks have larger bolt holes than what is used for the throttle linkage on a pickup. These bushings reduce the thread size down to the proper size so you can mount Dodge-style throttle linkage on the pump. Includes 3 bushings.  The bolt required that thre..

Set of 6 brand new CNC machined high flow delivery valve holders for a P7100 injection pump. This set has a 0.120" hole for the fuel to pass through. No Cores Required! MADE IN THE USA! No o-rings or copper washers are included.   ..

Limited Availability Includes all numbered items. We can get individual pieces if need be, CLICK HERE. Also, there is an optional Throttle Position Sensor bracket option.  ..

Got a 12-valve?Got an engine with a P-7100 Pump?You need The ADJUSTER From optimum economy to max power on the fly from inside the cab!The ADJUSTER by Attitude (pat pend)  (formerly Attitude Adjuster) gives you full control of your  12-valve Cummins or any other engine equipped with a Bosch P7100 in..

5000 RPM Governor Spring Kit (5K GSK)This 5,000 RPM kit utilizes the stock idle (large) spring and will idle at stock levels. We have installed this kit in several trucks locally and they all idled great and pulled hard past 4,000 RPM. Recommended for competition use only, very smooth, better throt..

High Flow 191 Delivery Valves For 1994-1998 P7100 Pumps Found on Dodge 12V Cummins Turbo Diesels. Do you need more fuel for your Dodge 12 valve Cummins?Check out these 191 Delivery Valves.They don't flow as much as laser cuts, but they are a definite improvement over your stock delivery valves! In..

Adjustable Timing Pump Gear for 1994-1998 Dodge 5.9L Cummins With P7100 Fuel Injection Pumps. Will also work on P pump conversions. Up to 40 degrees of timing adjustment in increments of 2 degrees. Hash marks allow for easier adjusting.Includes pump shaft key and all necessary hardware.DAP part num..

These should be replaced when you replace/upgrade your delivery valves. Bosch Part number: 2410101014..

Set of 6 brand new CNC machined high flow delivery valve holders for a P7100 injection pump. This set has a 0.093" hole for the fuel to pass through. No Cores Required! MADE IN THE USA! No o-rings or copper washers are included. ..

The CHEAPEST HORSEPOWER you can buy!APP's Billet Rack Cap (also sometimes called the rack plug), made of the highest quality Billet Aluminum, allows full rack travel of the Bosch P7100 injection pump.  The Attitude Rack Cap is drilled to 17mm, which is 4mm deeper than a stock rack cap.  This allows ..

When installing a bottom sump with your AirDog or Fass Pump most trucks end up with an open fuel supply and or return line. G & R Diesel's 1/2" or 3/8" aluminum plug will cap off these lines with ease, to keep fuel from seeping out of them and dirt from getting into your fuel tank. You no longer hav..

5000 RPM Governor Spring Kit (5K GSK)This 5,000 RPM kit does not utilize the stock idle (large) spring. We only recommend using these springs when your pump is sitting at a qualified pump shop being calibrated on a test stand. We have NOT had the best luck on installing these on a truck without havi..

BD-Power AFC Spring Kit for the 94-98 Dodge Cummins Diesel with Bosch P7100 injection pump. The P7100 uses an AFC housing assembly to control maximum fuel delivery under low boost conditions. This housing has several adjustments, one of which is its position frontward-rearward on the governor part o..

DescriptionDust Seal for 12 Valve Injector Bodies.-Sold IndividuallyPart#: D3909356..

Is your truck extremely low on power, and now drive like a strong 7.3L Powerstroke? If so, there's a possibility the diaphragm in your AFC (air fuel control) housing is torn. It doesn't happen very often, but it is possible. To verify, you can remove the AFC from your truck and apply 15-25PSI of sho..

Spacer for lift pump on Dodge 1994-1998.5 12 Valve Cummins. Used when removing the fuel heater. Cummins part number: 3914284..

High Flow 022 Delivery Valves For 1994-1998 P7100 Pumps Found on Dodge 12V Cummins Turbo Diesels. Do you need more fuel for your Dodge 12 valve cummins?Check out these 022 Delivery Valves. These Delivery Valves will deliver approx. 20% more HP for your 94-98 Dodge Cummins 12 Valve, but there will ..

The BD Power fuel stop plates install in the governor portion of the inline fuel pump to provide some substantial power gains. Made from heavy-duty thick aluminum to withstand the harsh engine operating conditions. Fuel Stop Plates Commonly known as a “cam plate”, BD’s Fuel Stop Plate controls the ..