1989-1993 Dodge 1st Gen 5.9L Fuel System Parts

Cummins 12 valve and 24 valve lift pump block off plate.  Covers the hole on 89-98 12 Valves that would normally have a lift pump bolted into it. Allows you to eliminate the lift pump bracket on 98.5-02 24 Valve Cummins trucks.03-18 trucks, this blocks off the ccv breather drainback port.   O-ring ..

Fits: 1989-1993 5.9L Cummins This Alliant Fuel Transfer Pump is a replacement part for you old and worn out fuel pump in your 1989-1993 Dodge 5.9L Diesel. It is the highest quality replacement Alliant pump at a reasonable cost.  Cross References: 3901425 3904374 3928143 396615..

The rubber components of the AFC (the diaphragm, foot shaft o-ring, and housing seal) were previously hard to find and often become neglected on aging 12v trucks. The AFC Housing Reseal Kit includes everything, so you can be sure your AFC housing is free of oil and boost leaks. Features: Co..

Adjust your 12v Cummins injectors with this injector shim kit. Perfect your injector install with this shim kit. PDD: 61214191100..

Secure your new upgraded fuel injectors with the Power Driven Diesel OEM Replacement 12v Cummins Injector Hold-Down Nut set. Designed for First and Second Gen 12v Cummins, this injector nut set ensures a secure fit for the fuel injector into the cylinder head, preventing any unnecessary leaking or h..

PROBLEM: If you are running an aftermarket pump that is mounted external of the fuel tank, you will need to install a draw straw or drill your fuel tank to accommodate a sump.  Each of these has some pretty significant drawbacks including the ¼ tank issues that result in cavitation ..

Have you upgraded from your factory mechanical lift pump to an electric pump? This block off will eliminate the void left by your stock pump. Complete with bolts, cover, and o-ring.Fleece Part Number: FPE-CUMM-FBOP..

CUMMINS GEAR REMOVER   VE , P7100 OR VP44 INJECTION PUMPS Removing the gear from a VE, P7100 or VP44 injection pump requires a specialized tool. Sure, you can cobble a pry bar or shade tree tool, but do you want to risk wrecking your expensive injection pump? Tork Tool is the l..

12v Return Tee with 2 Push Locks. Push Locks are 5/16"Return Tee, Cummins 5/16 pushlock w/ tapped hole for injector galley return when eliminating OE fuel filter. Part Number: 12VT..

This is for both washers and the check valve. Number 4 & 5 only. Cummins part number:  3918188, 3924726..

Black anodized lift pump block off fits Cummins 12 valve and 24 valve. O-ring groove machined into back side.  No need for leaking gaskets. Comes with stainless bolts and o-ring to seal it to the block.Keating: 020415-1-Black..

Mopar locking fuel cap. Full stainless steel locking assembly. Comes with two keys Meets Federal Fuel Safety Standards Mopar part number: 82400806 This product fits 760 vehicle variants.CHRYSLER: 9 models, 146 variants between 1984 and 1999.DODGE: 13 models, 307 variants between 1984 and 19..

12mm banjo bolt to 3/8" pushlock adapter fitting.Add on the optional high flow 12mm x 1.5 banjo bolt and seals for a complete kit. (PDPHF12MM) Part Number: PDP1438..

Backordered with No ETA   **Updated on 03/05/2024** The Draw Straw™ 3 Is the threaded version of the original DS2 for use with plastic or metal tanks in Dodge, Ford and GM trucks. This unit is a single port billet aluminum bulkhead fitting that requires a 3/4" hole to be dri..

Anodized billet aluminum Y-fitting with barbed ends for pushlock hose.  Fleece Part Number: FPE-FIT-Y06-BLK  ..

Fuel Sump Features: • 1/2" NPT Outlet Port • 1/2" NPT Return Port With Stand Tube  • Fully Functional Water Separator Sump • Does not require removal of fuel tank • Made in USA RCD: RCD-0000490001..

The XDP Push-Lock Fuel Pressure Tee XD200 is machined from aluminum with a pre-drilled & tapped 1/8" NPT port to accept a fuel pressure sender or hose. The 1/2 Push-Lock fitting makes it ideal for use with aftermarket fuel systems such as Airdog or FASS. Simply install this fitting in-line ..

Adapter sleeve to use 7mm intercooled injectors in a 9mm non-intercooled head.-Sold IndividuallyPart number: D3919358..

1/2" Push-Lock To 1/2" Bead Fitting   FASS: PLB-1212  ..

Prevent cold weather gelling of your fuel system with BD's PTC Heating element. Sandwiched between the water separator, pre-filter and/or the filter head, the BD fuel heater is perfect for cold weather warriors. The premade wiring harness with sealed electrical connectors offer qiuck and easy instal..

Prevent cold weather gelling of your fuel system with BD's PTC Heating element. Sandwiched between the water separator, pre-filter and/or the filter head, the BD fuel heater is perfect for cold weather warriors. The premade wiring harness with sealed electrical connectors offer qiuck and easy instal..

When installing a bottom sump with your AirDog or Fass Pump most trucks end up with an open fuel supply and or return line. G & R Diesel's 1/2" or 3/8" aluminum plug will cap off these lines with ease, to keep fuel from seeping out of them and dirt from getting into your fuel tank. You no longer hav..

Injector Install Kit for 1989 - 1998 Dodge 5.9L 12V Cummins B, C Series.By Interstate Mcbee Includes: 6: M-154087 Square Cut O-Ring 6: M-3903380 Horseshoe Shaped Banjo Connector Gasket/Washer 6: M-3920174 7mm Nozzle GasketCopper Sealing Washer (1.5mm Thick, ISB) 6: M-3923261 7mm Nozzle G..

Replacement Cummins throttle linkage rod for 1989 to 1991 Dodge Cummins Turbo Diesel 12 Valve with VE pump. Replaces Mopar 5011955AB.   Please compare to your original linkage before ordering. The threaded rod measures 4-1/4" long.   Part Number: 4089076..

Fuel Tank Cap (17591D) by Stant®. Diesel Only Keyed Alike. With Locking. A defective fuel cap can cause your vehicle to fail an emissions test, and allow up to 22 gallons of gasoline to evaporate in one year, wasting your money and polluting the environment. A Stant replacement fuel cap includes all..

The XDP Fuel Tank Sump with Built-In Fuel Return XD243 provides you with a perfect option to maximize fuel delivery, and customization when installing your aftermarket fuel system. Avoid the common 1/4 tank issues associated with in-tank draw straws used with fuel systems such as AirDog, FASS and ma..

Fits 89-93 Dodge 5.9L Cummins Diesel Trucks This fuel filter stud is used to delete fuel heater on 1st gen Cummins (89-93) Part number: J925954Also available from Cummins: 3925954..

This Pure Diesel Power's CNC Machined Fuel Filter head designed for the 89-02 Cummins 5.9L. This fuel filter comes standard with a port for a 1/8" NPT fuel pressure sensor to work alongside your fuel pressure gauge. A 1/8" NPT plug comes standard with the kit if you do not have a gauge for..

Injection Pump Fuel Return Line Number 2 in Image. This line, in theory, should fit 1989-1991 Dodge with the non-intercooled 5.9L Cummins diesel. HOWEVER, PLEASE enter your engine serial number above to verify it will fit before ordering.  Cummins part number 3905707...

Made for 89-91 5.9L Cummins engines that still utilize an injector with a 9MM tip Must order Quantity 6 Cummins part number: 3900808..

Return Fuel Line Injectors to Return Tee Number 7 in Image. This item may be a FACTORY ONLY item, which can cost additional, please call for availability.  Cummins part #3909696..

91.5-93 Dodge 5.9L Intercooled Cummins OEM Injection Line Set. Also referred to as fuel supply tubes. Does not include fuel line clamps. These lines will need to be painted. Click here if you are looking for all the lines. < Line Number Part Nu..

91.5-93 Dodge 5.9L Intercooled Cummins OEM Injection Line Set. Also referred to as fuel supply tubes. Does not include fuel line clamps. These lines will need to be painted. If you are looking for individual lines CLICK HERE. Part Numbers: 3920233 3920234 3920235 3920236 3920237 3..

Designed for our fuel filter head, but may fit other styles.  This sandwich fuel heater is recommended for trucks that consistently see temperatures below 10 degrees. Includes: Sandwich Heater XL Stud w/ Nut Wiring Harness Instruction Booklet Technical Support..

Set of 6, does not include clamps. Can be shipped clamped together in groups of 3 lines each for an additional fee. Stock replacement set. These are not OEM.   These lines are mild steel and should be painted These lines take 2-3 Business Days to build, please keep this in min..

Includes only parts circled from image! Part #10 is 3904519Part #11 is 3917716Part #12 is 3917747 (Includes two)Part #20 is 3920854 (Includes two)..

89-91 Dodge 5.9L Non-Intercooled Cummins OEM Injection Line Set. Also referred to as fuel supply tubes.Does not include fuel line clamps. These lines will need to be painted. Kit includes line part numbers: #1 3909438 #2 3903486 #3 3903487 #4 3903488 #5 3903489 #6 3903490 Kit part numbe..