Shop By Category
Your Cart

07.5-09 Dodge 6.7L Cummins Pusher 3.5" Mega Intake w/Pass Side Tube

07.5-09 Dodge 6.7L Cummins Pusher 3.5" Mega Intake w/Pass Side Tube
07.5-09 Dodge 6.7L Cummins Pusher 3.5" Mega Intake w/Pass Side Tube
07.5-09 Dodge 6.7L Cummins Pusher 3.5" Mega Intake w/Pass Side Tube
07.5-09 Dodge 6.7L Cummins Pusher 3.5" Mega Intake w/Pass Side Tube
07.5-09 Dodge 6.7L Cummins Pusher 3.5" Mega Intake w/Pass Side Tube
07.5-09 Dodge 6.7L Cummins Pusher 3.5" Mega Intake w/Pass Side Tube
07.5-09 Dodge 6.7L Cummins Pusher 3.5" Mega Intake w/Pass Side Tube
07.5-09 Dodge 6.7L Cummins Pusher 3.5" Mega Intake w/Pass Side Tube
07.5-09 Dodge 6.7L Cummins Pusher 3.5" Mega Intake w/Pass Side Tube
07.5-09 Dodge 6.7L Cummins Pusher 3.5" Mega Intake w/Pass Side Tube
07.5-09 Dodge 6.7L Cummins Pusher 3.5" Mega Intake w/Pass Side Tube
07.5-09 Dodge 6.7L Cummins Pusher 3.5" Mega Intake w/Pass Side Tube
07.5-09 Dodge 6.7L Cummins Pusher 3.5" Mega Intake w/Pass Side Tube

Available Options

$749.99

  • Part Number: PDC0709MW
  • Est. Ship Time: Some Built On Demand Contact to Confirm

Our 6.7L MEGA Intake Manifold is built around a 3.5" inlet that smoothly transitions to two 3" mandrel bent tubes. The twin tube design nearly doubles the outlet size of the stock manifold while minimizing the impact of the initial section of the number one injector line. Our design also allows for the use of a short bolt in place of the long driver-side flange bolt that passes right through the center of the stock manifold air plenum. This frees up airflow even more while maintaining the stock six bolt pattern for a proper seal. With this vast improvement over the stock manifold you can expect quicker turbo spool, lower EGTs, and less over all strain on your motor. This manifold also includes instructions, a polished stainless dipstick mount, port plugs, OEM gasket and hardware to make installing this intake extremely easy. This manifold is for off road use only.


Our 3.5" intercooler tubing is built using mandrel bent .060" thick tubing, and is a drastic improvement over factory 2.4" ID plastic plumbing. Our intake system also includes heavy duty 4-ply silicone couplers and stainless T-bolt clamps to make install simple. When using this kit, you do not have to try and cut the factory steel band off your tube in order to save the factory boots: just loosen the factory clamps and install the supplied parts.


Intercooler Compatibility: This product was designed to work with the factory intercooler, and as such will work with aftermarket intercoolers that mimic the factory inlet / outlet locations.





Features:

  • 50-200 degree Fahrenheit drop in EGT's
  • .5-1 MPG increase
  • Significant gain in throttle response
  • Faster turbo spool


Note: This product is not emission compliant. Off road use only. 

Pusher part number: PDC0709MW

WRITE A REVIEW

 

Please login or register to review

 
Lame California Prop 65 Notice