Powerstroke DCR Conversion Guide: Planning a CP4 Replacement
Replacing the factory CP4 pump with an S&S DCR injection pump involves more than selecting a compatible replacement part. This Powerstroke DCR conversion guide explains what owners of Ford 6.7L Powerstroke trucks should verify before converting, including fitment, installation requirements, fuel-system condition, and existing contamination. Pure Diesel Power carries diesel fuel-system components for these applications, including the S&S Diesel Motorsport CP4-to-DCR conversion kit.
The DCR conversion is intended to replace the original high-pressure fuel pump with a different design while retaining factory engine-control compatibility in supported applications.
The conversion can be considered while the original CP4 is still operating or as part of a properly diagnosed pump replacement. Those situations require different preparation.
If the existing pump has failed internally and released metal debris, replacing the pump alone may not address the entire repair.
Understanding the truck's starting condition is therefore one of the most important parts of planning the conversion.
What Changes During a 6.7 Powerstroke DCR Conversion?
The factory CP4 is a high-pressure injection pump that supplies fuel to the common rail system.
The pump must deliver the pressure required by the engine-control system while operating alongside the injectors, fuel rails, and other fuel-delivery components.
An S&S DCR conversion replaces the factory CP4 with a different high-pressure pump design.
The DCR pump was developed by S&S Diesel Motorsport and PurePower Technologies for the Ford 6.7L Powerstroke application.
Its documented features include:
-
Two-piston DCR pump architecture
-
Patented eccentric-drive pumping technology
-
Pressure-lubricated cam and bushings
-
Corrosion-resistant inlet metering valve
-
Compatibility with the factory ECU calibration
-
Pump displacement rated approximately 25% greater than the factory CP4.2
The additional displacement is a technical capacity specification.
It does not mean that the engine automatically receives 25% more fuel during normal operation or produces an equivalent increase in power.
S&S designed the DCR to operate with the factory fueling strategy in compatible vehicles.
What the Conversion Does Not Change
The pump conversion does not eliminate the need for fuel filtration, clean diesel fuel, or correct supply-side operation.
It also does not automatically correct:
-
Existing injector damage
-
Contaminated fuel rails
-
Debris remaining in fuel lines
-
Fuel supply restrictions
-
Faulty electrical connections
-
Unrelated fuel-pressure control problems
Those conditions must be evaluated separately.
A DCR conversion should not be treated as a universal repair for every symptom associated with low fuel pressure.
Confirm Vehicle Fitment Before Selecting a DCR Kit
Compatibility is the first major planning consideration.
The S&S DCR conversion is developed for supported Ford 6.7L Powerstroke applications, not for every diesel engine using a CP4 pump.
The manufacturer's current product information lists Ford F-250 through F-750 diesel applications across specified model years.
However, published fitment ranges have differed between product descriptions and installation documentation.
For that reason, buyers should verify the exact vehicle against the manufacturer's latest fitment information before ordering.
Information to Verify
Confirm the following:
-
Vehicle model and model year
-
Factory engine configuration
-
Existing high-pressure pump arrangement
-
Correct S&S conversion part number
-
Product-specific installation documentation
-
Any model-year-specific supporting components
The S&S Ford DCR conversion carries manufacturer part number 6.7F-DCR-1 and is also listed by Pure Diesel Power as SSD-6.7F-DCR-1.
The manufacturer's documentation identifies an additional vacuum pump gasket requirement for certain 2011–2016 applications.
That requirement should be reviewed when preparing an applicable truck for installation.
Modified Trucks Need Additional Review
A truck with aftermarket injectors, a modified fuel-delivery system, or a nonfactory calibration may require more evaluation than a stock vehicle.
The DCR pump's factory calibration compatibility should not be interpreted as approval for every modified engine configuration.
Existing modifications should be documented and checked against the manufacturer's current technical guidance.
Evaluate the Existing CP4 and Fuel-System Condition
Before beginning a DCR conversion, determine whether the original CP4 is functioning normally or has experienced a confirmed failure.
This distinction affects the overall repair plan.
Converting an Operating CP4
When the factory pump is still operating normally, the owner may be considering a proactive change in pump design.
The planning process focuses on correct fitment, required installation components, and ensuring the existing fuel system is in suitable condition.
That includes reviewing:
-
Fuel filter condition
-
Fuel quality
-
Existing fuel-pressure complaints
-
Relevant diagnostic trouble codes
-
Known supply-side problems
-
Any evidence of contamination
A working CP4 should not automatically be assumed to have internal damage merely because the owner has chosen a conversion.
Converting After a Suspected CP4 Failure
A different approach is needed when the truck has experienced hard starting, a no-start condition, reduced power, or abnormal fuel-pressure readings.
These symptoms may be associated with a high-pressure pump problem, but they are not exclusive to CP4 failure.
Low-pressure fuel supply problems, excessive injector return flow, sensor faults, and pressure-control issues can produce similar symptoms.
A confirmed diagnosis should come before purchasing a complete repair package.
Check for Metal Contamination
If the original CP4 has experienced internal mechanical damage, metallic particles may enter connected fuel-system components.
Depending on the failure and the system's fuel-routing arrangement, contaminated areas can include:
-
Fuel rails
-
High-pressure lines
-
Injectors
-
Return passages
-
Filter components
-
Other affected fuel-system circuits
Installing a new DCR pump does not automatically remove debris from these areas.
If contamination is present, the appropriate repair may require additional component replacement and manufacturer-approved cleaning procedures.
The diesel fuel contamination repair kits category covers application-specific parts packages intended for more extensive contamination repairs.
Prepare for the DCR Conversion Installation
The installation should follow the exact S&S Diesel Motorsport instructions for the selected vehicle application.
This guide provides planning considerations rather than a substitute for the manufacturer's installation procedure.
Review the Complete Kit and Instructions
Before installation, verify that the kit corresponds to the vehicle and that all required components are available.
Check:
-
Correct DCR pump and conversion part number
-
Required included fittings and hardware
-
Model-year-specific parts
-
Applicable gasket requirements
-
Current installation instructions
-
Availability of required tools and service information
Do not assume that instructions for one model year apply unchanged to another.
Mechanical Pump Timing Matters
An important distinction is the difference between ECU calibration and mechanical pump timing.
S&S states that the DCR does not require additional ECU tuning solely for the pump conversion.
However, the manufacturer also specifies that the DCR pump must be mechanically timed according to its installation instructions.
S&S identifies harmonics as an important reason for following the prescribed timing procedure.
These two statements are not contradictory.
Factory ECU calibration compatibility does not mean the physical pump can be installed without observing mechanical timing requirements.
Installers should follow the manufacturer's timing directions rather than estimating pump position or applying assumptions from another pump design.
Plan for High-Pressure Fuel-System Safety
Modern common rail diesel systems operate at extremely high pressures.
Incorrect handling can result in serious injury, component damage, or fuel leakage.
High-pressure connections should not be opened or loosened during operation as an informal diagnostic method.
Technicians should use the appropriate service information, procedures, tools, and precautions for the vehicle.
If the installer is not equipped to perform high-pressure fuel-system work, professional installation is appropriate.
Avoid Combining Incompatible Components
The manufacturer's Gen2.1 CP4 Disaster Prevention Kit is designed for the original CP4 arrangement.
S&S states that this kit is not compatible with, or required alongside, the DCR conversion.
A DCR installation plan should therefore use the parts identified for the DCR system rather than assuming previously selected CP4 protection components can be retained.
What to Check After a DCR Conversion
The work is not complete simply because the replacement pump is physically installed.
Before the truck returns to normal service, the installer should follow the manufacturer's specified checks and commissioning procedures.
Verify Fuel-System Integrity
The completed installation should be inspected according to the applicable service instructions.
That includes confirming that disturbed connections, fittings, and related components have been correctly installed.
Any fuel leaks or abnormal operating conditions must be resolved before normal use.
Confirm Normal Operation
After the system has been prepared according to the manufacturer's instructions, verify that it operates as intended.
Relevant considerations include:
-
Starting behavior
-
Fuel-pressure performance
-
Abnormal noises
-
Diagnostic trouble codes
-
Warning indicators
-
Fuel leakage
-
General engine operation
A problem appearing after conversion should be diagnosed rather than automatically attributed to the new pump.
Do Not Ignore Existing Diagnostic Codes
Rail-pressure-related faults may involve components other than the high-pressure pump.
For example, insufficient fuel pressure during cranking can be associated with supply problems, excessive internal leakage, control-valve faults, or other conditions.
Likewise, an electrical code may indicate a wiring or connector issue rather than mechanical pump failure.
Troubleshooting should follow the applicable diagnostic procedure and the manufacturer's technical guidance.
DCR Conversion Versus Other CP4 Protection Options
A DCR conversion is one approach to addressing the original CP4 pump arrangement.
Other products serve different purposes.
| Option | Primary purpose | Important distinction |
|---|---|---|
| Keep the factory CP4 | Continue using the original pump | Existing pump design remains |
| CP4 disaster prevention kit | Help limit debris spread during certain CP4 failures | Does not replace the CP4 |
| DCR conversion | Replace the CP4 with the S&S DCR design | Requires correct fitment and installation |
| CP3 conversion | Replace the original pump with a compatible CP3 arrangement | Platform-specific conversion requirements |
| Contamination repair kit | Replace components affected by existing contamination | Not equivalent to a preventive pump upgrade |
These options should not be selected based only on a general claim that one is more reliable than another.
The truck's actual condition, intended use, product compatibility, and repair objectives matter.
An owner whose CP4 has already contaminated the fuel system may need extensive repair regardless of which replacement pump is selected.
An owner with an operating CP4 is evaluating a different question: whether an alternative pump design is appropriate before a failure occurs.
For a broader explanation of the available approaches, read the CP4 vs CP3 vs DCR vs Disaster Prevention Kit Guide.
For additional background on the original pump and conversion considerations, review 6.7 Powerstroke CP4 Conversion Benefits.
Selecting a DCR Conversion for Your Powerstroke
A successful conversion plan starts with three decisions.
First, determine whether the truck is an approved application.
Second, establish whether the original fuel system is functioning normally or requires contamination-related repairs.
Third, review the manufacturer's complete installation instructions, including timing and model-year-specific components.
The S&S DCR conversion is designed to provide an alternative to the factory CP4 pump while maintaining factory engine-control compatibility in supported applications.
It is not a substitute for diagnosing existing fuel-system problems or repairing contamination.
For product-specific information, review the S&S Diesel Motorsport CP4-to-DCR Conversion Kit at Pure Diesel Power.
Confirm current fitment, required components, and manufacturer instructions before purchasing or scheduling installation.
Frequently Asked Questions
Click or tap any question below to open the answer.