Shop By Category
Your Cart

07.5-18 Ram 6.7L Cummins Banks 4" Inlet Monster-Ram Intake System

07.5-18 Ram 6.7L Cummins Banks 4" Inlet Monster-Ram Intake System
07.5-18 Ram 6.7L Cummins Banks 4" Inlet Monster-Ram Intake System
07.5-18 Ram 6.7L Cummins Banks 4" Inlet Monster-Ram Intake System
07.5-18 Ram 6.7L Cummins Banks 4" Inlet Monster-Ram Intake System
07.5-18 Ram 6.7L Cummins Banks 4" Inlet Monster-Ram Intake System
07.5-18 Ram 6.7L Cummins Banks 4" Inlet Monster-Ram Intake System
07.5-18 Ram 6.7L Cummins Banks 4" Inlet Monster-Ram Intake System
07.5-18 Ram 6.7L Cummins Banks 4" Inlet Monster-Ram Intake System
07.5-18 Ram 6.7L Cummins Banks 4" Inlet Monster-Ram Intake System

Available Options

$519.00

  • Part Number: 42790-xx
  • Est. Ship Time: Contact to Confirm Availability
 

Monster-Ram Intake Elbow Kit with Fuel Line, 3.5 inch Red Powder Coated for use with 2007.5-2018 Dodge/Ram 2500/3500 6.7L. Release that inner monster by feeding it a consistent, less restrictive airflow.

      Monster-Ram 6.7 power difference:
        The stock horn has quite a boost loss at the same flow, so now with a better flowing horn virtually all the boost produced by the turbos can get to the valves.

 Monster-Ram improves airflow from the intercooler. Flows 1008 cfm (77.01 lbs/min) compared to Stock's measly 432 cfm (33.00 lbs/min). Raises boost without increasing backpressure at the turbine. Result: a more responsive, power efficient engine. Up to four 1/8 inch NPT ports for flexibility! The top two NPT ports are positioned to allow for proper atomization directly into the center of the air mass while preventing wall wetting. Accommodates stock mounting points including Temperature and Pressure sensors, wire harness and dipstick tube. At Banks Power, just enough is never enough when it comes to engine airflow. Maximum power, performance and efficiency are the ultimate goals, but to make it all happen the engine has to breathe freely and without needless restrictions. Finding ways to pump your engine full of cooler, denser air has always been the key. Their High-Ram intakes have always whipped the competition. Their new Monster-Ram flat-out destroys it. Utilizing the latest in electronic computational fluid-dynamic technology, tested on the flow bench as well as on the dyno, and finally proven in the real world where the rubber meets the road, Monster-Ram is a beast that only Banks could have unleashed. A simple, direct-replacement casting, Monster-Ram is instant power, performance and acceleration gratification. The factory inlet is cramped and angular compared to Banks' larger, streamlined cast-metal Monster-Ram. It's the perfect upgrade whether you're just starting out or working to build a serious, purpose-built race machine. And with up to four ports for water/meth/propane/nitrous injection (or pressure/temp. sensors), the sky's the limit for performance expandability. Monster-Ram is CNC ported as well as the optional Banks Billet Intake Grid Heater Delete spacer.

Features:

  • Improves airflow from the intercooler
  • Raises boost without increasing turbine drivepressure
  • Larger & less restrictive than stock intake
  • Improves flow of oxygen-rich air into cylinders
  • Quicker throttle response
  • Outflows stock by up to 230%
  • 4 inch CNC machined inlet
  • Four 1/8 inch NPT ports (Top ports aimed for optimal atomization of Straight-Shot water-methanol)
  • Accommodates stock mounting points
  • Optimizes air pressure and distribution going into the intake manifold
  • Competitively priced
  • Includes Fuel Line, 4 to 3.5 inch Hump Hose and all necessary hardware

Fitment Note:

Will not work with stock boost tube

Part of the Banks Racing line

Does not accommodate emissions equipment

This is for Pure Race Use Only. Emissions equipment must be removed and requires a special ECM program available from others

Add the Billet Heater Delete Kit for optimal power (6.7L 1st Gen use P/N 42712) (6.7L 2nd Gen use P/N 42714)

Requires Banks Boost Tube Upgrade or custom boost tube


Cummins 6.7L ISB early 1st Gen 

- Driver & Passenger tubes - 25990 Boost Tube kit 

- Driver side only - 25991 Boost Tube kit


Cummins 6.7L ISB late 1st Gen 

- Driver & Passenger tubes - 25998 Boost Tube kit

- Driver side only - 25997 Boost Tube kit


Cummins 6.7L ISB 2nd Gen

- Driver & Passenger tubes - 25992 Boost Tube kit

- Driver Side only - 25994 Boost Tube kit


NOTE: Will not work with stock boost tube. Product puts inlet hose joint at the stock location. Part of the Banks Racing line, does not accommodate emissions equipment. Designed for pure race capability and is not emissions compliant, requires special ECU programming.


Part Number 42790 or 42790-PC

WRITE A REVIEW

 

Please login or register to review

 
Lame California Prop 65 Notice
Tags: Dodge , Ram , 6.7L , Cummins , Banks , Intake